Enthalpy of fusion

The enthalpy of fusion is the change in enthalpy resulting from heating one mole of a substance to change its state from a solid to a liquid. The temperature at which this occurs is the melting point.

The enthalpy of fusion is a latent heat, because during melting the introduction of heat cannot be observed as a temperature change, as the temperature remains constant during the process. The latent heat of fusion is the enthalpy change of any amount of substance when it melts. When the heat of fusion is referenced to a unit of mass, it is usually called the specific heat of fusion, while the molar heat of fusion refers to the enthalpy change per amount of substance in moles.

The liquid phase has a higher internal energy than the solid phase. This means energy must be supplied to a solid in order to melt it and energy is released from a liquid when it freezes, because the molecules in the liquid experience weaker intermolecular forces and have a larger potential energy.

When liquid water is cooled, its temperature falls steadily until it drops just below the freezing point at 0 °C. The temperature then remains constant at the freezing point while the water crystallizes. Once the water is completely frozen, its temperature continues to fall.

The enthalpy of fusion is almost always a positive quantity; helium is the only known exception.[1] Helium-3 has a negative enthalpy of fusion at temperatures below 0.3 K. Helium-4 also has a very slightly negative enthalpy of fusion below 0.8 K. This means that, at appropriate constant pressures, these substances freeze with the addition of heat.[2]

Contents

Reference values of common substances

Substance Heat of fusion
(cal/g)
Heat of fusion
(kJ/kg)
water 79.72 334.0
methane 13.96 58.41
ethane 22.73 95.10
propane 19.11 79.96
methanol 23.70 99.16
ethanol 26.05 108.99
glycerol 47.95 200.62
formic acid 66.05 276.35
acetic acid 45.91 192.09
acetone 23.42 97.99
benzene 30.45 127.40
myristic acid 47.49 198.70
palmitic acid 39.18 163.93
stearic acid 47.54 198.91
Paraffin wax (C25H52) 47.8-52.6 200–220

These values are from the CRC Handbook of Chemistry and Physics, 62nd edition. The conversion between cal/g and kJ/kg in the above table uses the thermochemical calorie (calth) = 4.184 joules rather than the International Steam Table calorie (calINT) = 4.1868 joules.

Applications

1) To heat one kilogram (about 1 litre) of water from 283.15 K to 303.15 K (10 °C to 30 °C) requires 83.6 kJ.
However, to melt ice and raise the resulting water temperature by 20 K requires extra energy. To heat ice from 273.15 K to water at 293.15 K (0 °C to 20 °C) requires:

(1) 333.55 J/g (heat of fusion of ice) = 333.55 kJ/kg = 333.55 kJ for 1 kg of ice to melt
PLUS
(2) 4.18 J/(g·K) = 4.18 kJ/(kg·K) = 83.6 kJ for 1kg of water to go up 20 K
= 417.15 kJ

2) Silicon has a heat of fusion of 50.21 kJ/mol. 50 kW of power can supply the energy required to melt about 100 kg of silicon in one hour, after it is brought to the melting point temperature:

50 kW = 50kJ/s = 180000kJ/h

180000kJ/h * (1 mol Si)/50.21kJ * 28gSi/(mol Si) * 1kgSi/1000gSi = 100.4kg/h

Solubility prediction

The heat of fusion can also be used to predict solubility for solids in liquids. Provided an ideal solution is obtained the mole fraction (x_2) of solute at saturation is a function of the heat of fusion, the melting point of the solid (T_{fus}) and the temperature (T) of the solution:

 \ln x_2  = - \frac {\Delta H^\circ_{fus}}{R} \left(\frac{1}{T}- \frac{1}{T_{fus}}\right)

Here, R is the gas constant. For example the solubility of paracetamol in water at 298 K is predicted to be:

 x_2  = \exp {\left(- \frac {28100 \mbox{ J mol}^{-1}} {8.314 \mbox{ J K}^{-1} \mbox{ mol}^{-1}}\left(\frac{1}{298}- \frac{1}{442}\right)\right)}= 0.0248

This equals to a solubility in grams per liter of:

 \frac{0.0248*\frac{1000 \mbox{ g}}{18.053 \mbox{ mol}^{-1}}}{1-0.0248}*151.17 \mbox{ mol}^{-1} = 213.4

which is a deviation from the real solubility (240 g/L) of 11%. This error can be reduced when an additional heat capacity parameter is taken into account [3]

Proof

At equilibrium the chemical potentials for the pure solvent and pure solid are identical:

\mu^\circ_{solid} = \mu^\circ_{solution}\,

or

\mu^\circ_{solid} = \mu^\circ_{liquid} %2B RT\ln X_2\,

with R\, the gas constant and T\, the temperature.

Rearranging gives:

RT\ln X_2  = - (\mu^\circ_{liquid} -  \mu^\circ_{solid})\,

and since

 \Delta G^\circ_{fus}  = - (\mu^\circ_{liquid} -  \mu^\circ_{solid})\,

the heat of fusion being the difference in chemical potential between the pure liquid and the pure solid, it follows that

RT\ln X_2  = - ( \Delta G^\circ_{fus})\,

Application of the Gibbs-Helmholtz equation:

\left( \frac{\partial ( \frac{\Delta G^\circ_{fus} } {T} ) } {\partial T} \right)_{p\,} =  \frac {\Delta H^\circ_{fus}} {T^2}

ultimately gives:

\left( \frac{\partial ( \ln X_2 ) } {\partial T} \right)  =  \frac {\Delta H^\circ_{fus}} {RT^2}

or:

 \partial \ln X_2   =  \frac {\Delta H^\circ_{fus}} {RT^2}*\delta T

and with integration:

 \int^{x_2=x_2}_{x_2 = 1} \delta \ln X_2 = \ln x_2  = \int_{T_fus}^T \frac {\Delta H^\circ_{fus}} {RT^2}*\Delta T

the end result is obtained:

 \ln x_2  = - \frac {\Delta H^\circ_{fus}} {R}\left(\frac{1}{T}- \frac{1}{T_{fus}}\right)

See also

Notes

  1. ^ Atkins & Jones 2008, p. 236.
  2. ^ Ott & Boerio-Goates 2000, pp. 92–93.
  3. ^ Measurement and Prediction of Solubility of Paracetamol in Water-Isopropanol Solution. Part 2. Prediction H. Hojjati and S. Rohani Org. Process Res. Dev.; 2006; 10(6) pp 1110 - 1118; (Article) doi:10.1021/op060074g

References